|Application:||Rubber Conveyor Belt Vulcanizing||Heating-up Time:||30 Mins|
|Cooling Time:||5 Minutes||Temperature Adjustment Range:||Max. 200ºC|
|Vulcanizing Temperature:||145ºC||Weight:||About 1860kg|
|Max. Capacity Pressure:||2.0Mpa||Power(w):||14.1 KW|
Hot Splicing Conveyor Belt Jointing Machine,
Aluminium Conveyor Belt Jointing Machine,
2.0Mpa Conveyor Belt Splicing Machine
Quick Fast Jointing Conveyor Belt Hot Splicing Conveyor Belt Jointing Machine
1.Light Aluminum alloy cross beams, high strength bolts and nuts suitable to exert a minimum pressureof 25kg/cm².
2.Voltage: 220V 380V 415V 525V 660V 1140V 50HZ 60HZ (Customize available according to your requirement)
3.Quick water cooling device: 15~20 minutes From 145 ℃ down to 80 ℃ or even lower
4.Cooling source: Water or Air
5.Heating source: Electricity
6.Heating time: from room temperature to vulcanization temperature need less than 20 minutes
7.Heating platen surface temperature difference: ± 5 ℃
8.The temperature adjustment range: 0 ~ 200 ℃ (custom)
9.Vulcanization pressure: Max 23kg/cm² (2.3MPa).
10.Automatic mute pressure pumps for operating pressure above 90 kg/cm².
11.Automatic control panel: insulating and waterproof, security alarm, Auto power-off when reach the vulcanization temperature. Upgraded explosion proof control box optional.
|Model||Width of rubber belt to be joined-up
|Total Power(KW)||Weight of heaviest part (Kg)||Overall dimensions LxWxH(mm)||Total weight
Note: Quick Fast Jointing Conveyor Belt Hot Splicing Conveyor Belt Jointing Machine
When order, pls supply below information, our technician will make a solution for you, or pls choose one model from bottom traditional sizes table
Normal vulcanizer model sheet:
A= Splice Length
B= Bet Width
C=Length of platen along the belt
D= Width of platen
measured square to beltline
E= Bias Ange
F=Width of platen along the belt on bias
Main Componets of Quick Fast Jointing Conveyor Belt Hot Splicing Conveyor Belt Jointing Machine
BEAM of Quick Fast Jointing Conveyor Belt Hot Splicing Conveyor Belt Jointing Machine
l Tension bolts made of high-strength steel, however, 2 kg less apiece than conventional steel tension bolts.
3. Lightweight aluminum platens use new rapid cooling system within platens.
4. Custom sizes, rectangular configurations and multiple platen arrangements are also available on request.
5. ELECTRONICS CONTROL CABINET
6． Pressure bag system, can used for both water and air, one time molding, without metal frame, light weight, testing pressure out of our factory is 2.5MPA (old design pressure bag fixed with metal frame and bolts, heavy weight)
A. Automatic pressure pump with pressure gauge, allows easy application of pressure up to 200PSI. For steel-cord belting, standard will be auto pressure pump. After use new cooling system in the heating platen, now also use pressure pump for cooling.
B. Cooling pump , when work with air compressor, air pressure, no pressure pump, such cooling pump can used for cooling. (Pls note that, if have any special requirements of the cooling pump working voltage, pls inform us before order, standard voltage is 220V single phase)
C. Manual Pump: Manual water pressure
Usually we provide the packing list as following:
|#1||Heating plate with build in water cooling device||2 Pieces|
|#2||Almex type pressure bag||1 Pieces|
|#3||Heating insulation plate||3 Pieces|
|#4||Standard Control Box||1 Sets|
|#5||Cross Beams||as vulcanizer|
|#6||Ratchet wrench||2 Handles|
|#7||Primary wire/cable with plugs 10 meters||1 Pieces|
|#8||Secondary wire/cable with plugs 5 meters||2 Pieces|
|#9||Electric pump||1 Set|
|#10||High pressure hose||15Mpa 5 Meters|
|#11||Clamp bolt, Nut, Gasket||10 sets|
|#12||Clamp Device (optional)||As request|
Contact Person: Miss. Lily Fu
Tel: +86 130 6133 2206